Gehl
Gehl V335
The bright segment is what Gehl V335 is rated to carry; the grey run past it is the rest of its tipping load. Bar length is tipping load drawn to the same scale on every machine on the site, so a short bar is a smaller machine and not a conservative rating.
Gehl publishes no list price for this machine, and we found no dealer listing worth quoting, so there is no number here to give you. What we can say is what the machines around it cost: the middle half of the 9 wheeled machines within 15 per cent of its capacity list between $67,909 and $79,590. That is a fact about them, not a quote for this one.
Part of the September 2025 large-frame launch, and the point where Gehl's wheeled range moves from Yanmar to a 100 hp Deutz TCD3.6. Capacity only climbs 100 lbs over the V325 but flow, power and headroom all step up with it.
Also sold as
The same machine is sold as the Manitou 3350V, which we do not list separately. Different paint and a different dealer network, same hardware.
Suits: Contractors running heavy hydraulic attachments who need power more than they need another 100 lbs of lift Its vertical lift path reaches highest at full extension, for loading high-sided trucks and stacking.
Lifting and reach
- Rated operating capacityWheeled rating convention
- 3,350 lbs
- Tipping load
- 6,702 lbs
- Lift height to hinge pin
- 134 in
- Lift path
- Vertical Lift
- Operating weight
- 9,835 lbs
Power and hydraulics
- Engine power
- 100 hp
- Engine
- Deutz TCD3.6
- Auxiliary flowStandard circuit
- 25 GPM
- Flow type
- Standard
- Warranty
- 2 yr / 2,000 hr
Fitted or available
What this machine can be ordered with. Some of these are standard and some cost extra, and which is which moves between trim levels, so check them against the quote rather than against this list.
What owners report
Summarised from the sources listed below. Nothing here was tested by us.
Slotting between the 72 hp V325 and the 114 hp V360, this is the middle of Gehl's September 2025 large-frame range and arguably the most coherent of the three. The extra engine over the V325 is what makes the 40 GPM high-flow option meaningful, because flow without the horsepower behind it just means an attachment that stalls under load. Product manager Nathan Ryan positioned the whole range against Caterpillar, JCB, Takeuchi and Case in what the trade calls the super skid steer class.
The platform's real changes are structural. Patent-pending lift arms slope away from the operator so material sheds rather than packing on, with hoses routed inside or underneath for protection, and R&D director Tyler Handel described the goal as visibility above and below the boom. Hydraulics are load-sensing with variable rate flow, letting the operator dial in what an attachment actually wants, and there is an adjustable creep mode with a boost pedal for planers and brooms. Controls are pilot joysticks mounted to the seat rather than electro-hydraulic. The cab gets a 7-inch colour display, backlit keypad with keyless start and a foot throttle, and Gehl quotes up to 50.3 hydraulic horsepower standard with 82 hp available on the boost option.
Attachments rather than pallets have to be the reason you are shopping large-frame - if you mostly need lift capacity, the cheaper V325 gets you within 100 lbs. Gehl publishes no price, so collect quotes under both the Gehl and Manitou badges, because the identical machine sells as the Manitou 3350V and whichever dealer is closer is the one worth buying from. Before signing, confirm the high-flow circuit and hydraulic boost are itemised on the build sheet, price the side counterweights separately, and accept that on a platform this new you are buying the warranty and the dealer as much as the machine.
What owners like
- The 40 GPM high-flow option at 3,450 psi is enough to run a large mulching head at its rated output rather than marginally, which is the practical dividing line between this class and the 30-34 GPM machines below it.
- 100 hp from the Deutz TCD3.6 leaves reserve to drive an attachment and the wheels at the same time, instead of bogging whenever the head loads up.
- Optional side counterweights lift rated capacity from 3,350 lbs to 3,800 lbs, a much bigger proportional gain than the counterweight kits on Gehl's smaller frames deliver.
- Bucket breakout across the large-frame range is quoted at 10,624 lbs with 7,041-7,116 lbs at the lift arm, so it digs as hard as it lifts.
- Serviceability was clearly a design target: grouped daily checks, grease fittings around the machine perimeter at walking height, a tilt-up hydraulic cooler with an optional reversible fan, and a tilting cab.
What owners complain about
- Only 6,702 lbs of tipping load sits under the 3,350 lb rating, and because Gehl quotes wheeled machines at 50% of tipping load that leaves genuinely little margin when a bucket loads unevenly or a pallet sits off-centre.
- Launched September 2025, so there is no service history, no used market and no independent read on what this platform does at high hours.
- At 9,835 lbs it carries real transport cost and enough ground pressure to mark surfaces a lighter machine would cross without trace.
- The Deutz engine is a different parts and service relationship from the Yanmar-powered machines lower in Gehl's own range, which fragments a mixed fleet.
- The capacity step over the V325 is 100 lbs while the engine step is 28 hp, so the two models are genuinely hard to choose between unless you know your work is hydraulically limited rather than capacity limited.
- Gehl publishes no list price for it, so there is nothing to check a dealer quote against except quotes from other dealers.
Drawn from constructionequipmentguide.com, compactequip.com, heavyequipmentguide.ca.
What buyers ask
V335 or V325 - how do I choose?
Is the V335 the same machine as the Manitou 3350V?
Does the 3,350 lb rating compare directly with a track loader's number?
Is there an electric version?
What does the optional hydraulic boost actually give me?
Put the Gehl V335 against
Machines in the same range
The rest of the Gehl line
Gehl
Gehl R105
$35,000
Also sold as the Manitou 1050R
- Engine
- 35 hp
- Aux flow
- 15 GPM
- Weight
- 4,200 lbs
Smallest wheeled skid loader in Gehl's lineup (sold in Manitou colors as the 1050 R), the R105 has a 1,050 lb rated capacity, a 34.7 hp Yanmar diesel under 25 kW emissions thresholds, and a narrow, low-profile frame. It's built for barns, hobby farms, and tight spots full-size machines can't enter.
Full sheet & owner reports
Gehl
Gehl R165
$47,000
Also sold as the Manitou 1650R
- Engine
- 68 hp
- Aux flow
- 20 GPM
- Weight
- 6,165 lbs
Value-priced digging and grading for farms, landscapers, and budget-minded contractors is what the Gehl R165 is for - a mid-frame radial-lift wheeled skid loader from Manitou Group (also sold as the Manitou 1650 R) with a 1,650 lb rated capacity and a proven Yanmar diesel.
Full sheet & owner reports
Gehl
Gehl V210
$58,000
Also sold as the Manitou 2100V
- Engine
- 69 hp
- Aux flow
- 22.9 GPM
- Weight
- 7,480 lbs
Introduced in 2023 as a mid-level vertical-lift wheeled skid loader (its Manitou-network twin is the 2100 V), the Gehl V210 slots between the radial R-series and the big V270 with a 2,100 lb rated capacity, a 69 hp Yanmar diesel, and a 120.5-inch hinge pin height for pallet and truck-loading work.
Full sheet & owner reports